| 
| 
If at first your confused give us a call 02 9756 2880
Bonethane is as easy as One, Two, Three
Did you know that we at Bonethane will cut up to 3 to 4 standard cuts free of charge?
Angles and power-hole cuts are not included. Simply pass the cutting list to a team member. For extra cuts a fee may be applied, please contact us for more details.
► Bonethane’s preferred adhesive is Parfix All Purpose, highly flexible silicone sealant which is available at Bunnings. The silicone must be in clear. This product is also mould and UV resistant.
If you have an accidental spill of silicone on the face of Bonethane, what do you do?
►Use either mineral turps, wax or grease remover. Apply product to effected area liberally to remove silicone. The residue should be removed immediately by washing area with warm soapy water. These solvents are available at Bunnings or your local super market.
► Bonethane must lay flat for first 3 hours prior to installation
►If you have white Kitchen and choose a white splash back please take into consideration that there are many variations of white. The A/white Splash can come off looking grey against white cupboards if you require further information about colour process please call our office.
►If you buy two sheets of the same colour from different stores for example, peel corner of masking a couple of centimetres to ensure colour consistency before installation. If multiple sheets are ordered of the same colour batch, this will not be necessary. If a variation is noted please call 0297562880 with proof of purchase from recognised distributor and we will promptly send out new sheets and pick up variations. Please note all masking must remain intact, except for the couple cm corners which allows for colour view.
► If ordering more than one sheet of the same colour it is advised to order of the same colour batch. This is to accommodate the colour variation ageing process. ISPS is not responsible for any inconsistencies due to aging of the sheet or variation in the sheet. All colours have a settling stage and colours beyond our control can vary slightly until they settle.
► Before mounting Bonethane to your wall, you can use the cardboard packaging as a template to gage placement of Bonethane.
► When applying silicone to corners, cut nozzle on an angle. Work upwards or forwards when applying silicone. Always remove excess silicone keeping a neat straight line. Be careful not to apply silicone to the face. If you run into trouble try gently rubbing mineral turpentine over the effected area, or contact Bonethane on (02) 9756 2880 if in doubt. IMPORTANT: Do not use thinners or abrasive cleaning products to remove or clean Bonethane. In most cases abrasive damage can be reversed.
► Use clear water proof kitchen or bathroom grade silicone to mount Bonethane to the wall in grid manner see instructions. (Parfix All Purpose, preferred silicone)
► Do not use coloured silicone on the back of Bonethane as this may penetrate through the Bonethane colour after installation.
► Do not apply silicone to the face of Bonethane. This should only be applied to the back of the product for mounting or when sealing corners. If you are faced with an accidental spill, try to gently remove with turps. If you are uncertain and require assistance please call (02) 9756 2880 our staff will be only to happy to help.
► Ensure blades are sharp for cutting and that battery operated tools are fully charged.
► If you are having trouble choosing a colour for Bonethane try painting some newspaper and holding it up to the area you wish to decorate.
DIY Friendly
► Bonethane is a DIY product. Added benefits of this product are that all cut outs and innovative angles can be done moments before installation, saving you the additional cost on all cut outs and installation processes.
► The following tools can be used: jigsaw; band saw, router, planer, drilling. Circular saw can be used only if you are experienced,all tools must have fine sharp blades, not big teeth as this will chop into the product, if cuts are not following in proper streamline (ie; stopping starting and varying speeds where big teeth are concerned). Fine blades will cut like butter with ease. Remember secure your sheet! Bonethane Premium can be cut with sharp fine blade stainless steel or plastic blade.
► The following items are also required, however, these are not included in the Bonethane pack: tile wedges, clear silicone (non acidic), protective goggles, dust mask, saws, level etc.
► Bonethane can be cut down and installed on site including power points and innovative angles which bring style to any home or commercial environment moments before installation.
Maintenance
► Light scratches can be buffed out using the same application as you would use on a vehicle. Bonethane is versatile product with an easy to care for surface.
► To ensure your product does not get damaged, you must keep Bonethane sitting upright against a wall, with a distance minimum of 8 cm to 10 cm from any standard ( electric kettle) heat expelled appliances.
► To clean: Strictly use a sponge soaked in soapy detergent and move in circular motion.
► To rinse: Use a towelling cloth with clean warm water & squeeze excess water. Then wipe in downward motion, repeat a second or third time, removing excess lather.
► To Dry: Do not polish. Bonethane will dry, providing the excess water becomes minimal when wiping down with warm damp towelling cloth, allowing to dry & shine.
► Always refer to Warranty Guidelines and Care Do’s and Don’ts when maintaining Bonethane product. Securing a 7 year warranty against ordinary conditions please refer to warranty reflecting maintenance of Bonethane.
Polishing edges:
Wet Dry sand paper.
Step 1: Sand edge using 180 grit.
Step 2: Sand edge using 240 grit
Step 3: Sand edge using 320 grit.
Step 4: Sand edge using 400 grit.
Another alternative is to get cotton bud with a little thinners and run down the edge, ensuring that the thinners do not touch the face of Bonethane as this will mark the product. Edges can be buffed, however Bonethane must be firmly secured as the rotational pull can cause a number of mishaps and may grab at the product flicking out of your hand or even flick up at you.
► When buffing only use light to medium pressure in a circular motion, be sure not to apply to much pressure.
► Before you apply Bonethane to the wall it is advised to fill any holes and paint a neutral colour on the wall in preparation of Bonethane placement. Bonethane can go over existing tiles, give the tiles a light sand and if tiles are dark just paint over in light neutral colour.
In preparation for cutting ensure that the Bonethane sheet is masked side down. The sheet must be firmly secured when cutting, so that it does not pull up at you. All blades must be sharp not blunt as this can chop into the product. For those people with battery aided power tools please ensure that batteries are fully charged as this will result in the same trauma to the product. Because of Bonethane’s exceptional strength properties these requests must be followed for premium results.
► Before you cut Bonethane ensure there is a 1 to 2 mm gap around the perimeter for expansion and contraction. Gaps can be filled with bathroom or kitchen grade water proof silicone.
► Masking should remain on until you are satisfied that Bonethane is secure from injury, peel off the masking.
► Clear bathroom or kitchen grade non-acidic silicone must strictly be used on the back of Bonethane to be mounted on the wall. (Preferred silicone- Parfix All Purpose)
► The silicone must be applied in a grid like fashion 10 to 15 cm apart. Remember clear non acidic silicone.